Exploring Plumbing Fundamentals When You Install a Bathtub
Call TodayWhat're your thoughts and feelings on A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging task. If the old bathtub is readily easily accessible, the task can move quickly; if you need to open a wall to eliminate the old tub and position the new bath tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will need an assistant to leave the old tub and set in the new one. Ensure you have actually qualified on your own for the job and also fit attempting it. As opposed to hiring a service provider to take control of a halfway-completed task, it is far better to take into consideration using one before you begin. Possibilities are you may need a professional plumber to make tube links.
This short article will assist you install a new tub in your washroom if you have actually already acquired a brand-new bathtub and also do not require to transform the arrangement of your previous water pipes.
Your tools and also product list ought to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the limited accessibility that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before proceeding to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Protect the faucet in place with the maker supplied backnut. As soon as the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap ports. The previous type must be connected to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wood boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub till the level reads level.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and additionally inspect the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub must wait till the tub has been used at least when as this will resolve it into its last placement.
Preparing for the Setup
First of all, the sustaining structure supplied with the bath should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack an inflexible seal, creating the water to pass through the wall surface in between the bath as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealant can crack fairly early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was guided to that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from someone on another web address. Sharing is good. Helping others is fun. Thanks for your time invested reading it.
The right fix? Ring!